Changing Guitar Strings
Have you changed your guitar strings this month?? This year??? Ever???!!! If you haven’t because you are intimidated by the process, this lesson is for you.
There are many benefits to keeping your strings fresh, including better tone, better feel and better dynamics to mention a few. Of course your guitar will look better. And a guitar with clean, new strings practically begs to be played!
Replace your guitar strings with the same gauge of strings as you used before. Your intonation may be off if you use a heavier or lighter set than you currently use. Most electric guitars come with extra-light or “9’s”. Acoustic guitars tend to come equipped with “light” strings. You can experiment with other gauges but this might entail a setup of your guitar to accommodate the change in tension. If you are unsure about string guages consult your local guitar shop or a knowledgable friend who can inspect your guitar.
 |
|
Preparation: You need the tools for the job. This includes a string winder, guitar tuner and wire cutters. Purchase a string winder. It will save you a great deal of time, well worth the dollar or two. Additionally, they are made to cleanly pull out the bridge pins on acoustic guitars. |
 |
|
Step 1 - Hold the guitar in your lap or on a padded table with the neck supported. The strings can be removed in any order, though starting at either the 1st or 6th string and working across keeps things organized. Loosen and remove the strings one at a time. Do not cut the string while it is under tension, as that is a jolt to the neck. |
Tip: Take advantage of the removal of the strings to clean the face of the guitar under these normally hard to reach areas.
 |
|
Step 2 - Insert the string into the bridge. For many electric guitars you will slide the guitar through the back. Pull the string through gently until you feel the ball end of the string seat in the bridge. For acoustics, put the bridge pin in while pulling upward. You should feel the ball slip into place as the pin is pushed down. |
 |
Step 3 - Feed the string through the corresponding tuning key. Allow enough slack for two to three windings around the tuning key. Winding the entire string will result in too many wraps causing the string to wrap upon itself and cause instability in tuning. Fewer than one complete wrap and the string may slip out. |
 |
After coming through the string hole, wind the string one-half way in the reverse direction around the tuning peg (clockwise when the tuning keys are on top; counterclockwise when the tuning keys are on the bottom). Kink the string to hold it in place. This will enable you to form a lock on the string to avoid slippage. |
 |
Step 4 - Wind the string with each wrap under the previous one, or closer to the base of the peg. This holds the strings in tune better and looks neater. You can help by keeping slack out of the string with your free hand and guiding the string downward. If your guitar has string trees on the headstock, have the string pass under the tree as you wind the string up to pitch. |
 |
Wind evenly, making sure that each wrap goes below the previous one. Each winding should be snug up against the previous one. |
 |
Step 5 - Tighten the string up to pitch. Don’t tighten so quickly that you break the string before you ever get to play on it! Next, stretch the string gently along its length. You should find that the string has gone flat. Retune the string. This stretching will minimize your retuning for the first days of your new strings. Trim off the excess string length with wire cutters. Repeat on each string. |
Clean up - Get rid of the old strings. They are no fun to step on with bare feet. And not good for your vacuum cleaner either!
Finally, to maximize the life of your strings, wash your hands before you play and wipe down the strings with a clean cloth after you practice. This will slow the build up of oils and dirt on the string which dull their look and sound.
Now make music. Happy picking.
Parts Of The Guitar
Learning the parts of the guitar is fundamental. The most common guitars used today can be classified as either Acoustic Guitars or Electric Guitars. Both types share the same three basic areas in common: Head, Neck and Body.
The head of the guitar (or ‘headstock’ as some prefer) is where the tuning keys are found. Where the guitar head and neck meet is the nut. The nut slots the strings and provides string height in relation to the neck. The neck has frets to shorten the depressed string by defined distances. The fingerboard (not the frets) is where we press down the strings. Not all guitars have position markers but they are used to help number the frets.
The body of the guitar defines the difference between Acoustic and Electric guitars. Acoustic guitars have a soundhole to focus the acoustic energy of vibrating strings. Electric guitar have pickups, which are small magnets that sit underneath the strings. When a vibrating steel string moves against the magnet a small electrical signal is produced and sent throught the output jack. Electric guitars can have various combinations of pickups, some type of pickup selector switch to choose the pickup used and volume and/or tone controls for those pickups.
The bridge of the guitar is where the strings attach to the body. The saddle is the part of the bridge the string passes over.
Your basic six-string guitar. Play yours today!
Storm Stenvold
GuitarTeacher.com
Stay up to date by subscribing to the website RSS feed or email summaries.
Recent Posts
Ask The Teacher
Professional guitar support available 24/7! Stop web searching and start playing!About
My name is Storm Stenvold. Welcome to my online lesson studio, Guitar Teacher.com!
I teach individual and group guitar lessons online (since 2001) and have taught guitar for 17 years. I was a founding faculty member of ...read more